Видео

This makes me feel better because I did this and wasn’t sure if this was the correct way to do it.

Thanks i will reinforce my tea biscuits so they will not fall in tea

What about inner piers ? Do they carry more floor load because the bearers resting on them carry floor loads in all four directions?

the best video on this topic i have watched so far thank you

Our building code in usa/california requires the rafter has minimum 1.5in bearing onto the top plate, so just using the rafter tie bracket is not legal, and frankly that seems a very bad idea to have the rafter bear on just a tiny point. What I do at least on sheds is use the bracket and glue in the wedge. That wedge is exactly the same size as you cut off the end of the rafter at the peak to attach it to the ridge board!

What happens if a length of wall is not equally divisible by 450 or 600? Say for example you have a wall that’s 3350/600, would you still space by 600 and split the difference at the end of the wall?

What do you do in the evening that a wall length on the plan is not perfectly divisible by 450 or 600mm, how would you space out your studs?

After taking the 1st set of readings, I assume that when you reposition the level that the telescope needs to re-leveled before the 2nd set of readings. Is that correct?

this is the greatest video i've ever seen in my life. zero fluff.

I'm 100% convinced, that if our state and federal government were serious about housing affordability and building new houses to ease this, they should pay you (and others like you) at least $300,000 a year and give you a dedicated team and unlimited resources to pump out videos on how we construct quality houses in Australia.

How can we calculate hip length if end triangle is not symmetrical but splayed .

Thanks so much !

in example A would there be an issue with the ceiling joist support because the beam isn't in the middle of the room?

Hey mate great video, do you ever use battens behind your cladding?

does the going include the nose of the step that overhangs the stringer dimension?

Thanks

Interesting I'm a student and would like to learn more from you please 🙏..watching from PAPUA NEW GUINEA 🇵🇬

Any reason you would advise against using 200x45 i-joists for the rafters? I'm building a livable garden shed 3600x4800 and happen to have some ijoists on hand, planning a 1mtr overhang on the high side and 400mm on the back. 5mtr span in total.

Great video mate. I’ve searched to see if you have been asked this already but I couldn’t see it. Would it be beneficial to lay a plastic sheet behind the wall, between it and the blue metal to prevent water coming through it?

Awesome work

Thanks 🙏🙏🙏

Hi, thank you very much for your excellent knowledge sharing. I am currently having a house to be built and at the brick stage，however, I don't see any sarking/sisilation layer behind the bricks, nether the flashing, although I did see some weep holes between the bricks. I am very confused, it looks like the bricks got lay up straight against the wood. Can any one please help me with 🥲my question?

Well shown, thanks for the video!

O

BuildSum guy for PM

Great Summary - you should create a program that works out doing this for a 3800mm x 2400mm shed frame

How many inch is over hang at the Ridge of Dutch gable roof.

Awesome video, much appreciated. Obviously you cant stop the concrete from cracking, but does moisture eventually pass up the crack and rust the rio?

Thank you for the detailed figure showing the terms for each things

bro i don't mean to but i feel like you are speaking gibberish. you should always pitch to the dumbest member of the audiance im told. pls say this in American. also no pun intended.

These videos are top notch both visually and auditory, been 10 years but no other content creator tops these

What about a steel frame building? By the way your video's are brilliant. Very well explained and also why you do what you do.

Another great video thanks

Well done simple video!

out of infinite numbers u uses 7572 mm

Intermediate level must be relative to backsigh level.. please check yout calculations

Yumm dumb ? But whats the software u r using ? Or if any one may no

2:53

for the oblique angle roof, the ridge coming off it doesn't seem straight (very minimal). I could be wrong... I noticed when that ridge was drawn... just wondering if it is dead straight?

How far out can you come 4 metres to much or just 3.5meters max

Thanks mate. Calvary blessings.

What about for a gable roof how do you calculate the different heights of each stud thanks lov these videos

Put simply & perfectly explained thank you for this video. Even more wholesome is seeing everyone's replies from years before! Legend

We have a high retaining wall in our back garden (about 8ft) that holds back our neighbours garden which is alot higher than ours. It does have small drainage pipes at the bottom of the wall, however the wall is constantly wet in patches. Could this be because the backfill has mixed and there is now soil directly behind the wall? The wall was built by our house builder so not sure what they have done behind it 😅

I’m guessing this only applies to timber construction as opposed to steel framing

Dont know about putting a sand bed but good presentation 👌🏻

beautiful but how do you get center of the cause I don't understand the half span you are using

Excellent video as always 👍 do you have a similar video but with taking levels with a laser and staff for excavation?

I'm busy framing out a small bathroom on a small off grid cabin. Came across this completely by accident and picked up at least 5 great tips on things I hadn't through about. Not a professional, just doing this for a small personal project. Old video but still so good, thanks!

I want to express my sincere gratitude for the significant impact your videos have had on my understanding of the construction industry. As a student in the field, I've found your content incredibly informative and insightful. Your work has greatly expanded my knowledge and perspective. Thank you for your invaluable contributions.